What is a blank in metal spinning?
The blank (also called the disc) is the flat, usually circular piece of sheet metal clamped on the spinning lathe before forming starts. The roller lays the blank onto the rotating mandrel in a series of passes until the sheet takes the shape of the mandrel.
Getting the blank size wrong costs time either way: a blank that is too small cannot complete the part, while an oversized blank wastes material, adds cycle time and makes flange wrinkling more likely. This metal spinning blank size calculator gives a first estimate for common shapes in seconds.
The constant-area principle behind blank calculation
In conventional spinning the wall thickness stays roughly the same. If the thickness does not change, preserving volume means preserving surface area: the area of the flat blank equals the mid-surface area of the formed part. Because the area of a circle is πD²/4, the blank diameter follows directly from the area:
The mid-surface is the surface halfway through the sheet thickness. With thin sheet, using inside or outside dimensions makes little difference; with thicker sheet the gap grows. Measure diameters and heights at the middle of the wall where you can, for example the inside diameter of a cup plus one sheet thickness.
D = √(4A / π)
A: mid-surface area of the part · D: blank diameter
Blank diameter formula for a cylindrical cup
For a flat-bottomed cylindrical cup with diameter d and height h, the surface area is the bottom disc plus the side wall: A = πd²/4 + πdh. Substituting this into D = √(4A/π) gives the blank diameter calculation most workshops use:
D = √(d² + 4·d·h)
Worked example: for d = 100 mm and h = 50 mm, D = √(10,000 + 20,000) = √30,000 ≈ 173.2 mm. The corner radius at the bottom is ignored here; a large radius makes the result slightly smaller.
Blank size for a cone or truncated cone
For a truncated cone closed at its small end (bottom diameter d₁, top diameter d₂, height h), the area is the bottom disc plus the lateral surface of the frustum. First find the slant height s of the side wall, then the area:
Entering d₁ = 0 turns the calculation into a full, pointed cone. With d₁ = d₂ the result matches the cylindrical cup formula, which is a handy consistency check.
s = √(h² + ((d₂ − d₁) / 2)²)
A = π·(d₁/2)² + π·(d₁/2 + d₂/2)·s
Worked example: for d₁ = 60 mm, d₂ = 120 mm and h = 80 mm, s = √(6,400 + 900) ≈ 85.4 mm, A ≈ 26,985 mm² and D ≈ 185.4 mm.
Blank diameter for a hemisphere or dome
A hemisphere of diameter d has a surface area of πd²/2. Put into D = √(4A/π), this simplifies neatly to D = √2 · d, so the blank is about 1.414 times the sphere diameter. If the dome has a cylindrical rim of height h at its open end, add πdh to the area.
D = √2 · d
With rim: D = √(2·d² + 4·d·h)
Worked example: a 100 mm hemisphere needs D ≈ 141.4 mm; adding a 20 mm rim raises it to D ≈ 167.3 mm.
Complex profiles: start from a known area
For reflectors, funnels and stepped profiles, the most practical route is to read the part's mid-surface area from your CAD model. Enter it with the “Enter area” option and the calculator applies the same D = √(4A/π) relation. Add the largest part diameter if you also want to see the spinning ratio.
Worked example: A = 25,000 mm² gives D = √(100,000 / π) ≈ 178.4 mm.
Conventional vs shear spinning: why the blank differs
All of the formulas above are for conventional spinning. In shear spinning the material does not move radially; it slides along the axis while the wall is deliberately made thinner. That is why the blank diameter is taken as roughly equal to the largest diameter of the part.
For a conical part, the formed wall thickness is estimated with the sine law, where α is the half-cone angle between the wall and the axis of rotation. The calculator's shear mode takes the largest diameter, the blank thickness and the angle, and returns the blank diameter and the estimated wall thickness.
t = t₀ · sin α
t₀: blank thickness · t: formed wall thickness
Worked example: t₀ = 2 mm and α = 30° give t = 2 × 0.5 = 1.0 mm.
Trim allowance: extra material for the rim
The open edge of a spun part is rarely perfectly even, so it is usually trimmed afterwards. To allow for this, add a trim allowance c per side of the blank. The allowance is entered as a length per side rather than a percentage of the diameter, so small and large parts keep the same trimming distance.
D_total = D + 2·c
Worked example: D ≈ 173.2 mm with c = 5 mm gives a blank of 183.2 mm. How much allowance you need depends on the trimming method, the waviness of the rim and shop practice.
What the spinning ratio (β) tells you
The calculator also shows the ratio of the total blank diameter to the largest part diameter. It is a rough indicator of how much deformation the part asks of the blank. Higher ratios usually need more passes and a more careful pass plan, and in some cases intermediate annealing between passes.
Because a suitable range depends on the material, sheet thickness, roller and mandrel, the calculator does not suggest a limit. Your own trials and your material supplier's data are the most reliable guide.
β = D_total / d_max
Worked example: a 100 mm cup spun from a 183.2 mm blank has β ≈ 1.83.
Common mistakes in blank diameter calculation
The arithmetic is simple, but these slips are common on a first part:
- Using inside or outside dimensions instead of mid-surface dimensions; the error grows with sheet thickness.
- Forgetting the trim allowance, or adding it as a percentage of the diameter.
- Sizing a shear-spun part with the conventional formula, which gives a blank far larger than needed.
- Leaving corner radii, flanges or curled edges out of the area.
- Sending the calculated diameter to production without a trial piece.
Programming guide, glossary and metal spinning CAM
The links between blank diameter, spinning ratio and pass design are covered in more depth in the metal spinning programming guide. Short definitions of the terms used here are in the metal spinning glossary. If you want to turn a DXF profile into a pass plan and G-code, take a look at the metal spinning CAM software.
Results are first estimates based on the assumption that wall thickness stays constant and the mid-surface area is preserved. Enter dimensions measured at the middle of the sheet thickness, or allow for the effect of thickness. The real blank size depends on material, process conditions and trimming method, so confirm it with a trial piece before production. This tool is not a substitute for engineering judgement.