Create account

GLOSSARY · METAL SPINNING

Metal spinning glossary

Short definitions of the terms used in metal spinning and CNC spinning programming. Each term links to the guide section or metal spinning CAM feature where it is covered in more detail.

Last updated: · KSOTech Engineering Solutions

Blank (disc)

The flat, usually circular sheet before spinning starts. Its diameter is estimated from the part's surface area or largest diameter.

Mandrel (chuck / former)

The rotating tool mounted on the spindle that carries the inner form of the part. The sheet is formed onto it.

Roller (spinning tool)

The forming tool that presses the sheet onto the mandrel while turning on its own axis. Its nose radius affects finish and force.

Pass (stroke)

One forming movement of the roller over the sheet. In conventional spinning a part is completed in many passes.

Forward pass

A pass in which the roller moves from the mandrel base towards the rim, laying the sheet onto the mandrel.

Back pass (backward pass)

A pass in which the roller returns from the rim towards the mandrel. It gathers the flange and reduces wrinkling.

Conventional spinning

Spinning in which the sheet is laid onto the mandrel over many passes and wall thickness stays roughly constant.

Shear spinning (shear forming)

Spinning in which the wall is deliberately thinned and material shifts along the axis. The blank is close to the part's largest diameter.

Sine law (sine rule)

Wall thickness estimate in conical shear spinning: t = t₀ · sin α (α: half-cone angle).

Flow forming

A related process in which a tube or thick preform is stretched and thinned along its axis by rollers. Not covered by KSOTech CAM.

Spin forming (metal spinning)

Another name for metal spinning, often used for CNC and large parts.

Spinning ratio

Blank diameter divided by mandrel diameter (β = D₀ / d). Larger ratios need more passes; each material has a limiting value.

Wrinkling (flange buckling)

Waviness when material gathered in the flange buckles. Large pass steps or missing back passes are typical causes.

Cracking (tearing)

Separation in the wall caused by excessive thinning or work hardening.

Thinning

Reduction of wall thickness during forming. Intended in shear spinning, unwanted in conventional spinning.

Annealing

Heat treatment that restores formability to a work-hardened material; may be needed between passes.

Work hardening (strain hardening)

Hardening and loss of ductility caused by plastic deformation. Pronounced in stainless steel.

Tailstock (follower)

The counterpart that clamps the blank against the mandrel so they rotate together.

Flange

The part of the sheet that still extends outward and has not yet been laid onto the mandrel.

Trim allowance

Extra blank diameter added to cut off the uneven rim after forming.

Springback

Elastic recovery of the sheet after the roller withdraws; a source of dimensional deviation.

Teach-in (playback)

Programming by driving the roller on the machine while the control records the motion.

Offline programming

Preparing the program on a computer instead of at the machine. Metal spinning CAM is the tool for it.

Metal spinning CAM (CNC spinning software)

Software that prepares spinning passes, simulation and machine-ready G-code from the part drawing.

G-code (ISO 6983)

The programming language that defines motion and function commands for CNC machines.

Post-processor (post)

The component that converts the CAM path into the G-code format a specific control expects.

G00 / G01 / G02 / G03 (motion commands)

Rapid move, linear feed, and clockwise / counter-clockwise arc commands.

R vs I/J/K arcs (arc format)

Arcs defined by radius (R) or by centre offsets (I/J/K); depends on the control.

Diameter / radius mode

Whether X values mean diameter or radius. Turning-type controls usually use diameter.

DXF

A common CAD file format for 2D drawings. In spinning the mandrel or part profile is supplied as DXF.

Toolpath

The path followed by the roller centre, offset from the mandrel profile by sheet thickness and roller radius.

Toolpath simulation

On-screen animation of the roller motion. It is not FEA process simulation.

Mandrel clearance (roller gap)

The gap between roller and mandrel; about one sheet thickness in the final pass.

Approach / retract

Safe moves at the start and end of each pass that prevent mandrel collisions.

Hot spinning

Spinning with the material heated during forming, for thick or hard-to-form materials.

CNC spinning lathe (CNC spinning machine)

A spinning machine that moves the roller under program control. Programs come from teach-in, hand-written G-code or CAM.